Do chainsaws use lots of bar oil? Your chainsaw has a separate reservoir designed to hold bar and chain oil. In most saws, the bar and chain oil reservoir holds enough oil to last as long as a tank of fuel. So, whenever you refuel your gas chainsaw, you should add bar and chain oil as well, every time.
Is chainsaw oil the same as bar oil?
Petroleum-based bar and chain oil has been used for ages, and it's probably still the most common lubricant today. It is typically labeled specifically as “bar and chain oil”. A lot of the big chainsaw brands also make bar and chain oil. For example, you can buy it from Oregon, Stihl, Husqvarna, etc.
What can I use instead of bar oil?
Here are four suggestions.
Why does my chainsaw use so much bar oil?
What causes a chainsaw to leak oil? As the oil is pumped from the tank through to the guide bar, air begins to replace the space where the oil was previously stored. If there isn't proper ventilation of the oil tank, a vacuum can occur and reduce the flow of oil to the guide bar.
What weight is chainsaw bar oil?
Similar to motor oil, chainsaw bar oil is available in various weights. The lightest oil is a 10W formula, while thicker oil may be up to 50W. A 30W chainsaw bar oil is generally considered standard for warm weather usage.
Related guide for Do Chainsaws Use Lots Of Bar Oil?
Can you use 10w30 for bar and chain oil?
Can I Use 10w30 for Chainsaw Bar Oil? Yes, though it is not ideal for use in the winter. A 10w30 oil is multi-weight, meaning it will perform well in cold and heat. Yet 10w30 weight motor oil will be very tacky and viscous once the chainsaw heats up and starts to run.
Can you use engine oil as bar oil?
While motor oil is not the best substitute for chainsaw bar oil, it will work as a temporary measure if find you have no other option. The downside of motor oil is that it's not sticky enough to stay on the bar and chain. So, when you're using the chainsaw, the motor oil will fling off as you cut and make quite a mess.
Can you use 2 stroke oil for chainsaw bar oil?
One final note: This article recommends using vegetable oil to replace chain oil in chainsaws. However, this does NOT mean replacing “mix” oil which is used for the gas mix. For mix oil, you must use the petroleum-based 2-stroke mix oil recommended by the chain saw manufacturer.
Can you use old motor oil for chainsaw bar?
Some people caution against using motor oil on a chain saw, but not for safety reasons or concerns about equipment. Bar and chain oil is stickier than regular motor oil, so it stays on the chain longer.
What kind of oil can I use for chainsaw bar?
Rapeseed-based (usually called canola) oil is currently the most common environmentally compatible chain-and-bar lubricant. Vegetable-based oils are triglycerides or natural esters that come from agricultural crops.
What happens if you run a chainsaw without bar oil?
No bar oil equals increased friction and heat. That adds up to a huge increase in chain and bar wear. Without bar oil, the chain teeth, drivers and links will all wear far more quickly. The increased friction can cause teeth to break.
Can I use olive oil for chainsaw?
However, keep in mind that every oil has a different viscosity and so will act slightly differently in your chainsaw. Other vegetable oils most commonly used in chainsaws are: Olive oil – thicker than canola but not good at low temperatures. Sunflower oil – thinner than regular chain oil.
Can you leave oil in chainsaw?
Chainsaws should not be stored with their oil and fuel tanks full. Each time that a new chainsaw or one that is very clean is run without cutting it will spread oil around the guide bar, chain and saw body in the form of a fine mist.
How do I know if my chainsaw is oiling enough?
How often should you oil a chainsaw?
How often should I lubricate the sprocket in the tip of my bar? It is recommended that you grease the bearing in the tip of the bar each time you refuel. Make sure to grease the tip at the end of the day as well to help prevent moisture from entering the bearing as the bar cools.
What's the viscosity of chainsaw bar oil?
For this reason, bar and chain oil should suit most loggers. They usually have a 10W relative weight during winter and 30W during warm weather conditions. You can check most oils authenticity by putting on the chainsaw and looking for any oil spills at about 8 inches on the other side.
What is special about 2-stroke oil?
A 2-stroke oil will lubricate the engine components by association with the fuel (either by mixing with it or by spraying during combustion), so this oil contains components that promote its combustion.
What is machine oil?
Sewing machine oil is a lubricant specifically made for sewing machine parts, recommended to be used approximately every 8 hours of sewing. The use of sewing machine oil lessens the friction between the machine's parts, keeping them from grinding on one another and wearing down.
Can I use 4 stroke oil in a chainsaw?
Don't use an oil mix in a 4-stroke engine
If it is a 2-stroke engine and you forget the oil, you will damage the engine. However, if you have a 4-stroke engine, you should make sure you only use pure gas – otherwise, you will also risk damaging your expensive chainsaw.
Can I use two cycle engine oil in a chainsaw?
Generic brand oils may not be designed to operate at the temperatures and rpm of modern two stroke chainsaws. To ensure a long trouble free life out of your modern two cycle engine, we strongly recommend using only high quality two stroke oil designed for air cooled high performance engines.
Can I use synthetic oil in my chainsaw?
*Can I use synthetic oil in my chainsaw fuel? Just like their use in lawnmowers, synthetic oils have been demonstrated to have superior combustion characteristics over mineral oils on top of delivering great lubrication on chainsaw engines. Synthetic oils will leave you with a much cleaner engine.
What is SAE30 oil?
SAE30 is a straight 30 weight oil used on your lawn mower and other 4 cycle outdoor equipment. SAE30 weight oil is rated only at the full operating temp of the engine. This means it is much higher than 30 when cold. Sometimes so thick that it cannot flow if it is cold enough out. The W means winter.
How tight should your chainsaw chain be?
A properly-tensioned chainsaw chain should still be just a little loose on the chainsaw guide bar, but the chain needs to be tight enough that you can't pull the drive links out of the bar nose.
Can gear oil be used as chain lube?
Of course you can use gear oil on your chain. It's an extremely good high pressure viscous lubricant, and unlike engine oils, it does not contain detergent additives which make engine oil less resistant to water washout.
When should you throw away a chainsaw chain?
Chainsaw feels unbalanced, cuts unevenly, or rattles when in use. In short, if you have attempted to balance your cutting teeth, are certain of your depth gauge, and the tension is properly adjusted, but the saw still doesn't cut correctly- then you need to replace the chain.
Why does my chainsaw blade go dull so fast?
With a single contact with the ground while running, a chainsaw can become very dull. This is because the ground contains sand and dust which is abrasive and contains a lot of tiny rocks. To avoid such occurrences, avoid cutting wood placed on the ground.
What should you not cut with a chainsaw?
Don't Cut With a Dull Blade
Cutting with a sharp blade actually extends the life of your chain saw. That's because a sharp blade pulls itself into the wood, while a dull blade requires lots of downward pressure. That pressure wears out the bar, drive links, clutch sprocket and clutch.
Can you use sunflower oil in a chainsaw?
If using a saw to cut meat, then vegetable oil is the obvious choice so the meat tastes good (you can use sunflower, canola, palm oil etc).
How long do chainsaw bars last?
On average, a chainsaw bar could last ten years unless it becomes damaged or bent. However, how long a chainsaw bar lasts depends on hours of use. If you only use your saw occasionally and maintain it properly, a bar could last as long or longer than the chainsaw.
Is it OK to cut wet wood with a chainsaw?
Does this pose any risk to your chainsaw? In all honesty, no! The additional moisture found on wet wood will not make any difference to the cutting process. It doesn't place any additional resistance on the chainsaw, and no additional effort is required to cut through it.